View TSOP77330_7239935.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 1 ir receiver modules for remote control systems tsop773.. vishay semiconductors mechanical data pinning: 1, 4 = gnd, 2 = v s , 3 = out features ? continuous data transmission possible ? very low supply current ? photo detector and preamplifier in one package ? internal filter for pcm frequency ? supply voltage: 2.7 v to 5.5 v ? improved immunity against ambient light ? capable of side or top view ? insensitive to supply voltage ripple and noise ? two lenses for high sensitivity and wide receiving angle ? narrow optical filter to redu ce interference from plasma tv emissions ? compliant to rohs directive 2002/95/ec and in accordance to weee 2002/96/ec description the tsop773.. is a two lens miniaturized receiver module for infrared remote control systems. one pin diode per lens and a preamplifier are assembled on a leadframe, the epoxy lens cap is designed as an ir filter. the demodulated output signal can be directly decoded by a microprocessor. the tsop773.. is optimized to better suppress spurious pulses from fluorescent lamps, lcd, tvs, or plasma displays. this component has not been qualified according to automotive specifications. block diagram application circuit 20953 1 2 3 4 parts table carrier frequency noisy environm ents and short bursts (agc3) 30 khz TSOP77330 33 khz tsop77333 36 khz tsop77336 38 khz tsop77338 40 khz tsop77340 56 khz tsop77356 30 k v s out demo- gnd pass agc input pin band dulator control circuit 2 3 1, 4 20445-1 c 1 ir receiver gnd circuit c r 1 + v s gnd transmitter with tsalxxxx v s v o 17170_7 out the external components r 1 and c 1 are optional to improve the robustness against electrical overstress (typical values are r 1 = 100 , c 1 = 0.1 f). the output voltage v o should not be pulled down to a level below 1 v by the external circuit. the capacitive load at the output should be less than 2 nf. ** please see document ?vishay material category policy?: www.vishay.com/doc?99902
www.vishay.com document number: 83346 2 rev. 1.1, 14-feb-11 tsop773.. vishay semiconductors ir receiver modu les for remote control systems note ? stresses beyond those listed und er absolute maximum ratings may cause permanent damage to the device. this is a stress ratin g only and functional operation of the device at these or any other cond itions beyond those indicated in the operational sections of t his specification is not implied. exposure to absolute ma ximum rating conditions for extended pe riods may affect the device reliability. typical characteristics (t amb = 25 c, unless otherwise specified) fig. 1 - output active low fig. 2 - puls e length and sensitivity in dark ambient absolute maximum ratings parameter test conditi on symbol value unit supply voltage v s - 0.3 to + 6 v supply current i s 5ma output voltage v o - 0.3 to (v s + 0.3) v output current i o 5ma junction temperature t j 100 c storage temperature range t stg - 25 to + 85 c operating temperature range t amb - 25 to + 85 c power consumption t amb ? 85 c p tot 10 mw electrical and optical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit supply current e v = 0, v s = 5 v i sd 0.65 0.85 1.05 ma e v = 40 klx, sunlight i sh 0.95 ma supply voltage v s 2.7 5.5 v transmission distance e v = 0, test signal see fig. 1, ir diode tsal6200, i f = 400 ma d40m output voltage low i osl = 0.5 ma, e e = 0.7 mw/m 2 , test signal see fig. 1 v osl 100 mv minimum irradiance pulse width tolerance: t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e min. 0.3 0.45 mw/m 2 maximum irradiance t pi - 5/f o < t po < t pi + 6/f o , test signal see fig. 1 e e max. 30 w/m 2 directivity angle of half transmission distance ? 1/2 50 deg e e t t pi *) t v o v oh v ol t po 2) t 14337 optical test signal (ir diode tsal6200, i f = 0.4 a, n = 6 pulses, f = f 0 , t = 10 ms) output signal t d 1) 1) 3/f 0 < t d < 9/f 0 2) t pi - 4/f 0 < t po < t pi + 6/f 0 *) t pi 6/f 0 is recommended for optimal function 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.1 1 10 10 2 10 3 10 4 10 5 e e - irradiance (mw/m2) t po - output pulse width (ms) 21391_1 output pulse width input burst length = 950 nm, optical test signal, fig.1
document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 3 tsop773.. ir receiver modules for remote control systems vishay semiconductors fig. 3 - output function fig. 4 - output pulse diagram fig. 5 - frequency dependence of responsivity fig. 6 - sensitivity in bright ambient fig. 7 - sensitivity vs. supply voltage disturbances fig. 8 - sensitivity vs. electric field disturbances e e t v o v oh v ol t 600 s 600 s t = 60 ms t on t off 94 8134 optical test signal output signal , (see fig. 4) 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 1 10 10 2 10 3 10 4 10 5 e e - irradiance (mw/m2) t on , t off - output pulse width (ms) 21392_1 t on t off = 950 nm, optical test signal, fig. 3 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.7 0.9 1.1 1.3 f/f 0 - relative frequency 16925 f = f 0 5 % f(3 db) = f 0 /10 e /e - rel. responsivity e min. e 0 0.5 1 1.5 2 2.5 3 3.5 4 0.01 0.1 1 10 100 e e - ambient dc irradiance (w/m 2 ) e e min. - threshold irradiance (mw/m 2 ) correlation with ambient light sources: 10 w/m 2 = 1.4 klx (std. illum. a, t = 2855 k) 10 w/m 2 = 8.2 klx (daylight, t = 5900 k) wavelength of ambient illumination: = 950 nm 20757 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1 10 100 1000 vs rms - ac voltage on dc supply voltage (mv) 21394 e e min. - threshold irradiance (mw/m 2 ) f = f 0 f = 20 khz f = 30 khz f = 100 hz f = 10 khz 0 50 100 150 200 250 300 350 400 450 500 0 500 1000 1500 2000 2500 3000 f - emi frequency (mhz) e - max. field strength (v/m) 20747
www.vishay.com document number: 83346 4 rev. 1.1, 14-feb-11 tsop773.. vishay semiconductors ir receiver modu les for remote control systems fig. 9 - max. envelope duty cycle vs. burst length fig. 10 - sensitivity vs. ambient temperature fig. 11 - relative spectral sensitivity vs. wavelength fig. 12 - horizontal directivity fig. 13 - vertical directivity fig. 14 - sensitivity vs. supply voltage 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 0 20 40 60 80 100 120 140 burst length (number of cycles/burst) max. envelope duty cycle 21590-7 e e = 2 mw/m2 tsop773.. t amb - ambient temperature (c) e e min. - threshold irradiance (mw/m 2 ) 21397 0.15 0.2 0.25 0.3 0.35 0.4 0.45 - 30 - 10 10 30 50 70 90 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 750 800 850 900 950 1000 1050 1100 1150 21425 - wavelength (nm) s ( ) rel - relative spectral sensitivity 0.8 0.9 1.0 0.6 0.4 0.2 0 0 30 10 20 40 50 60 70 80 d rel - relative transmission distance 21427 0.8 0.9 1.0 0 30 10 20 40 50 60 70 80 d rel - relative transmission distance 21428 0.6 0.4 0.2 0 0.20 0.25 0.30 0.35 0.40 0.45 0.50 1.5 2.5 3.5 4.5 5.5 234 5 v s - supply voltage (v) e e min. - sensitivity (mw/m 2 ) 21398
document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 5 tsop773.. ir receiver modules for remote control systems vishay semiconductors suitable data format the tsop773.. is designed to suppress spurious output pulses due to noise or disturbance signals. data and disturbance signals can be distin guished by the devices according to carrier frequenc y, burst length and envelope duty cycle. the data signal should be close to the band-pass center frequency (e.g. 40 khz) and fulfill the conditions in the table below. when a data signal is applied to the tsop773.. in the presence of a disturbance sign al, the sensitivity of the receiver is reduced to insure that no spurious pulses are present at the output. some examples of disturbance signals which are suppressed are: ? dc light (e.g. from tungsten bulb or sunlight) ? continuous signals at any frequency ? strongly or weakly modula ted noise from fluorescent lamps with electronic ballast s (see fig. 15 or fig. 16) fig. 15 - ir signal from fluorescent lamp with low modulation fig. 16 - ir signal from fluorescent lamp with high modulation note ? for data formats with long bu rsts (10 carrier cycles or long er) we recommend the tsop772.., ts op774.. because of the better no ise suppression. 0101520 time (ms) 16920 ir signal 5 0101520 time (ms) 16921 ir signal 5 tsop773.. minimum burst leng th 6 cycles/burst after each burst of length a minimum gap time is required of 6 to 35 cycles ? 10 cycles for bursts greater than a minimum gap time in the data stream is needed of 35 cycles > 6 x burst length maximum number of continuo us short bursts/second 2000 recommended for nec code yes recommended for rc5/rc6 code yes recommended for sony code yes recommended for recs-80 code yes recommended for rcmm code yes recommended for r-step code yes recommended for xmp code yes suppression of interference from fluorescent lamps even critical disturbance signals are suppressed (e.g. waveform of figure 15)
www.vishay.com document number: 83346 6 rev. 1.1, 14-feb-11 tsop773.. vishay semiconductors ir receiver modu les for remote control systems package dimensions in millimeters assembly instructions reflow soldering ? reflow soldering must be done within 72 h while stored under a max. temperature of 30 c, 60 % rh after opening the dry pack envelope ? set the furnace temperatures for pre-heating and heating in accordance with the re flow temperature profile as shown in the diagram. excercise extreme care to keep the maximum temperature below 260 c. the temperature shown in the profile means the temperature at the device surface. since there is a temperature difference between the component and the circuit bo ard, it should be verified that the temperature of the device is accurately being measured ? handling after reflow should be done only after the work surface has been cooled off manual soldering ? use a soldering iron of 25 w or less. adjust the temperature of the sold ering iron below 300 c ? finish soldering within 3 s ? handle products only after th e temperature has cooled off 6.6 0.1 3.2 1.27 3 x 1.27 = 3.81 (4x) 2.2 (1) 1.2 0.2 gnd vs out gnd (2.2) 2.2 (3.4) (r 1.3) 2.5 0.5 0.1 0.8 (1.8) 3 pick and place area proposed hole layout from component side (for reference only) specifications according to din technical drawings not indicated tolerances 0.15 drawing-no.: 6.550-5297.01-4 issue: 3; 02.09.09 marking area tool separation line (0.635) (1.65) 0.8 1.8 1.27 3 x 1.27 = 3.81 (3x) mold residue mold residue 6.8 21576
document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 7 tsop773.. ir receiver modules for remote control systems vishay semiconductors vishay lead (pb)-free reflow solder profile taping version tsop..tr dimensions in millimeters 0 50 100 150 200 250 300 0 50 100 150 200 250 300 t (s) t (c) 255 c 240 c 245 c max. 260 c max. 120 s max. 100 s 217 c max. 20 s max. ramp up 3 c/s max. ramp down 6 c/s max. 2 cycles allowed 19800 2 1.75 7.5 16 8 4 7.1 3.3 0.3 2.8 ? 1.5 min ? 1.5 direction of feed 1.34 ref. 4 4 drawing-no.: 9.700-5337.01-4 issue: 1; 16.10.08 specifications according to din technical drawings 21577
www.vishay.com document number: 83346 8 rev. 1.1, 14-feb-11 tsop773.. vishay semiconductors ir receiver modu les for remote control systems taping version tsop..tt dimensions in millimeters specifications according to din technical drawings drawing-no.: 9.700-5338.01-4 issue: 3; 09.06.09 21578 2 1.75 7.5 16 8 4 3.3 ? 1.5 min. ? 1.5 direction of feed 4 7.1 3.35 0.3 4
document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 9 tsop773.. ir receiver modules for remote control systems vishay semiconductors reel dimensions in millimeters leader and trailer dimensions in millimeters cover tape peel strength according to din en 60286-3 0.1 n to 1.3 n 300 10 mm/min. 165 to 180 peel angle label standard bar code labels for finished goods the standard bar code labels are product labels and used for identification of goods. th e finished goods are packed in final packing area. the standard packing units are labeled with standard bar code labels before transported as finished goods to warehouses. the labels are on each packing unit and contain vishay semicond uctor gmbh specific data. 16734 trailer leader no devices min. 200 min. 400 start end devices 96 11818 no devices
www.vishay.com document number: 83346 10 rev. 1.1, 14-feb-11 tsop773.. vishay semiconductors ir receiver modu les for remote control systems dry packing the reel is packed in an anti-humidity bag to protect the devices from absorbing moisture during transportation and storage. final packing the sealed reel is packed into a cardboard box. a secondary cardboard box is used for shipping purposes. recommended method of storage dry box storage is recommended as soon as the aluminum bag has been opened to preve nt moisture absorption. the following conditions should be observed, if dry boxes are not available: ? storage temperature 10 c to 30 c ? storage humidity ? 60 % rh max. after more than 72 h under these conditions moisture content will be too high for reflow soldering. in case of moisture absorptio n, the devices will recover to the former condition by drying under the following condition: 192 h at 40 c + 5 c/- 0 c and < 5 % rh (dry air/nitrogen) or 96 h at 60 c + 5 c and < 5 % rh for all device containers or 24 h at 125 c + 5 c not suitable for reel or tubes. an eia jedec standard jstd-020 level 4 label is included on all dry bags. eia jedec standard jstd-020 level 4 is included on all dry bags vishay semiconductor gmbh standard bar code product label (finished goods) plain writing abbreviation length item-description -18 item-n u m b er ino 8 selection-code sel 3 lot-/serial-n u m b er batch 10 data-code cod 3 (yww) plant-code ptc 2 q u antity qty 8 accepted b y acc - packed b y pck - mixed code indicator mixed code - origin xxxxxxx+ company logo long bar code top type length item-n u m b er n8 plant-code n2 se qu ence-n u m b er x3 q u antity n8 total length -21 short bar code bottom type length selection-code x3 data-code n3 batch-n u m b er x10 filter -1 total length -17 aluminum bag label reel 15973 caution this bag contains moisture-sensitive devices 1. shelf life in sealed bag: 12 months at < 40 c and < 90 % relative humidity (rh) 2. after this bag is opened, devices that will be subjected to soldering reflow or equivalent processing (peak package body temp. 260 c) must be 2a. mounted within 72 hours at factory condition of < 30 c/60 % rh or 2b. stored at < 5 % rh 3. devices require baking befor mounting if: humidity indicator card is > 10 % when read at 23 c 5 c or 2a. or 2b. are not met. 4. if baking is required, devices may be baked for: 192 hours at 40 c + 5 c/- 0 c and < 5 % rh (dry air/nitrogen) or 96 hours at 60 c 5 c and < 5 % rh for all device containers or 24 hours at 125 c 5 c not suitable for reels or tubes bag seal date: (if blank, see barcode label) note: level and body temperature defined by eia jedec standard jstd-020 4 level 22522
document number: 83 346 www.vishay.com rev. 1.1, 14-feb-11 11 tsop773.. ir receiver modules for remote control systems vishay semiconductors esd precaution proper storage and handling procedures should be followed to prevent esd damage to the devices especially when they are removed from the antistatic shielding bag. electro-static sensitive devices warning labels are on the packaging. vishay semiconductors standard bar code labels the vishay semiconductors st andard bar code labels are printed at final packing areas. the labels are on each packing unit and contain vishay semiconductors specific data. 22178
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.

▲Up To Search▲

Price & Availability of TSOP77330

	To Download TSOP77330 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .